So now you’re probably thinking “isn’t there another guide about this?” like @cinnamonroll_cat 's guide, I’m going to tell you no. The difference is that this guide explains how to perform sound by clicking the piano.
Now I will explain how I made the piano perform sound: zone/trigger triggered = sentries activate, also zone/trigger wired to wire repeater, wire repeater time delay= 0.5, wire repeater wired to sentries deactivate, Sentry 1 & Sentry 2 have 9999 health, Sentry 1= Team 1, Sentry 2= Team 2, Sentry 1 has max difficulty, Sentry 2 has lowest difficulty. In which gadgets will be used like the zapper has a sound and most of the time Sentry 1 will use the gadget 1-3 times. So then Zone/Trigger used= 1-3 note(s).
And how much gadgets are there in gimkit, answer= A HANDFUL= A HANDFUL of different notes. In this guide I will be demonstrating the sentry way of sound with zappers but you can change the gadget to any other if you want to have another sound.
Now there are also other ways to make sounds but for now this guide will focuse on how to get sounds from sentries.
So now I will show you how to make a FULLY functional piano.
for every note you have you will need: 1x zone, 4x barriers, 2 sentries.
Step one
GET A PIANO!!! using barrier art or this guide
Step two
Now have your trigger or zone over each note like this
Step three
Zone settings should look like this
or if you had trigger settings it would look like this
Step four
Get a wire repeater and set it to these settings
Step five
Connect your trigger to the wire repeater like this
or if you have a zone it would look like this
Step six
Now after you have wondered what the heck has a barrier to do with a piano other than barrier art. You just trust me. Anyways you need to create a box with the barriers like this.
Step seven
Now get two sentries and place them in the boxes made of barriers that should look like this
Ignore the wires
Step eight
Now remember that wire repeater? Connect it to the sentries.
Wire repeater → deactivate sentry
Wire repeater → deactivate sentry
Do this for the two sentries
That should look like this. For both sentries (I feel like I am not clear enough) but do this for TWO sentries in the box
That means you should see this screen two times and connect it two times, and as I was saying this is how it should look like
*sighs, DO THIS TWO TIMES THIS SHOULD BE HOW THE WIRES LOOK LIKE FOR NOW
Step nine
This is going to be the final step. Me be like: **ugh, finaallyyy.* Now it is very IMPORTANT you follow the exact same settings except for gadgets. So for sentry 1 these are the settings (meaning these settings only apply for 1 Sentry).
Sentry 1 settings
*Still Sentry 1 settings
Sentry 2 settings
*Still Sentry 2 settings
Final product
(I will add on how to do extra animation)
Extra animation
Equipment
Get the equipment which is: +1 zone +2 barrier +1 wire repeater. You should disassemble the piano carefully. Here is what all the equipment should look like.
Step 1
Set all the equipment to the right settings. WAIT! Did you make a smaller and darker barrier? Look at the picture in equipment. But anyways here are the settings for the equipment.
Zone
You should already have this if you did the guide fully.
Big barrier/Barrier 1
You should already have this if you did the guide fully.
Small barrier/Barrier 2
Wire repeater
Step 2
Connect the wires:
Zone (player entered zone) → Wire repeater
Wire repeater → Big barrier/Barrier 1 (activate)
Wire repeater → Small barrier/Barrier 2 (deactivate)
Wire 1
Wire 2
Wire 3
Final product for animation
Here it is:
Finally done!!! No wait we need a poll
- 1/10
- 2/10
- 3/10
- 4/10
- 5/10
- 6/10
- 7/10
- 8/10
- 9/10
- 10/10
